Pool Volume Calculator

Find how many gallons or liters your pool or hot tub holds, for any shape, then save it for every other calculator.

Type of pool
Shape
Measured in

Measure the width at evenly spaced points along the length (3 to 6 points). Leave unused boxes empty.

Depth

Type feet as 16 or 16'6". Depth means water depth, measured from the floor to the water line.

Your pool holds

Fill in the boxes and your answer appears here.

How to use it

  1. Pick the type of pool and the shape closest to yours.
  2. Measure the water surface, not the deck or coping. A 100 ft tape measure and a second person make this a five-minute job.
  3. For depth, measure from the floor up to the water line at the shallow and deep ends. Above-ground pools and hot tubs need one depth only.
  4. Press Save to My Pool. Every other calculator on this site will then start with your volume already filled in.
Where to measure: length and width from above, and water depth at the shallow and deep ends LengthWidth LengthOval: width isacross the middle ABLength Freeform: widths at even spacing Kidney: A = narrow end, B = wide end
Measure the water surface from above: length along the longest line, widths straight across.
Side view: shallow and deep end depths are measured from the floor up to the water line ShallowDeepWater line
The tool averages the two ends. That works for the usual long, even slope.

Worked examples

In-ground rectangle, 32 × 16 ft, 3½ ft shallow end, 6½ ft deep end.

Average depth = (3.5 + 6.5) ÷ 2 = 5 ft. Volume = 32 × 16 × 5 = 2,560 cubic feet. Each cubic foot holds 7.48 gallons, so the pool holds about 19,150 gallons (72,500 liters).

Above-ground round, 24 ft across, water 4½ ft deep.

Surface = 3.1416 × 12 × 12 = 452 sq ft. Volume = 452 × 4.5 × 7.48 = about 15,230 gallons. The same pool with water at 4 ft holds about 13,540 gallons, so the water depth matters more than people expect.

How it's calculated

Every shape is surface area × average depth × 7.48 gallons per cubic foot (one cubic foot is exactly 7.4805 US gallons, or 28.32 liters). Many charts round this to 7.5, which adds about a quarter of a percent.

  • Rectangle: length × width.
  • Round: 3.1416 × radius × radius, where the radius is half the diameter.
  • Oval: most above-ground ovals and many in-ground ovals have straight sides and half-circle ends. Area = (length − width) × width + 3.1416 × (width ÷ 2)². Using the ellipse formula on this shape under-counts by about 12%, which is the most common volume mistake on other calculators.
  • Ellipse: 3.1416 × (length ÷ 2) × (width ÷ 2), for a true egg-shaped curve with no straight sides.
  • Kidney: (A + B) × length × 0.45. This is the long-standing trade approximation and is usually within about 10%.
  • L-shape: the two rectangles added together.
  • Freeform: the widths measured at even spacing along the length are added up and multiplied by the spacing (length ÷ number of widths + 1). It treats both ends as coming to a point, so it suits rounded freeform pools better than square-ended ones.

Sloped pools use the average of the shallow and deep end. If your deep end is a short, steep hopper rather than a long slope, the true average is a little lower than this, so knock off about 5%.

The units and formulas are listed with the rest of our methods on How we calculate.

Why your gallons matter

Every chemical dose scales with volume. If you guess 20,000 gallons and the pool holds 14,000, every bag and jug is 40% too much. Being within 10% is good enough, because you will add chemicals in stages and retest anyway. Being off by a third is not.

If the pool was recently filled from a metered supply, the water meter gives you a second check. Read it before and after a top-up of a known depth: US meters usually count in gallons or in cubic feet (multiply cubic feet by 7.48).

Questions people ask

How many gallons is a 16 × 32 pool?

It depends on depth. At an average depth of 5 ft it holds about 19,150 gallons. At 4½ ft it holds about 17,240 gallons, and at 5½ ft about 21,060.

How many gallons are in a 24 ft round above-ground pool?

With 4 ft of water, about 13,540 gallons. With 4½ ft of water, about 15,230 gallons. Measure the water depth rather than the wall height.

How do I find the average depth of my pool?

Add the shallow end depth and the deep end depth and divide by 2. Measure from the floor to the water line, not to the top of the wall or the coping.

How accurate does my pool volume need to be?

Within about 10% is fine for chemicals. Doses are added in stages with a retest between them, so a small error gets corrected. A large error, such as using the wall height instead of the water depth, leads to over-dosing.

Is my oval pool an oval or an ellipse?

If the long sides are straight and the ends are half circles, choose Oval. Almost all above-ground oval pools are built this way. Choose Ellipse only if the outline curves all the way around like an egg.

Estimates only. Product strengths vary from jug to jug and lose strength with age, so treat every amount here as a starting point. Follow the product label, add in stages, and retest before swimming. For stubborn algae, equipment faults or surface damage, call a pool professional. Full disclaimer.

Embed this calculator

Pool service companies and bloggers are welcome to put this calculator on their own site. Copy the code below. Please keep the credit line under it.

My Pool

Saved in this browser only. Nothing is sent to us. Every calculator fills itself in from here.