How to use it
- Test total alkalinity (TA) and pH. Add stabilizer (CYA) if you know it.
- Enter a target. If you saved your pool, the target is set for the way you chlorinate.
- To raise alkalinity you get a baking soda amount, split into parts if it is large. To lower it you get a round-by-round acid and aeration plan.
Raising alkalinity
Use sodium bicarbonate. Pool-store "alkalinity increaser" and grocery-store baking soda are the same chemical, and the grocery version is usually cheaper per pound. It raises alkalinity a lot and pH only a little, which is why it is the right tool here. Soda ash also raises alkalinity, but it pushes pH up hard, so save it for when pH is low too.
Lowering alkalinity
There is no chemical that lowers alkalinity alone. Acid lowers alkalinity and pH together; aeration raises pH and leaves alkalinity where it is. Alternate the two and alkalinity steps down while pH comes back each time. Trying to do it in one big acid dose sends pH below 7, which etches plaster and corrodes metal heaters and ladders.
How long it takes depends on how much you have to drop and how hard you aerate. Pools with a waterfall or spa spillover finish a 40 ppm drop in a few days. Pools with a single return can take a week or two.
Worked example
Raising: 16,000 gallons, TA 60 ppm, target 90 ppm.
The rise is 30 ppm. Baking soda raises 10,000 gallons by 10 ppm per 1.4 lb, so 30 ppm in 16,000 gallons takes 1.4 × 3 × 1.6 = 6.7 lb. That is right at the 30 ppm size where the calculator starts splitting doses, so it goes in all at once and you retest after six hours.
Lowering: the same pool at 150 ppm, target 90 ppm, 31.45% acid.
Dropping 60 ppm takes about 25.6 fl oz of acid per 10 ppm per 10,000 gallons: 25.6 × 6 × 1.6 = about 246 fl oz in total, close to two gallons, spread over several rounds of acid and aeration.
How it's calculated
Alkalinity is reported as ppm of calcium carbonate. Each 10 ppm is 0.2 milliequivalents per liter. Baking soda supplies one equivalent per 84 g, giving 1.40 lb per 10 ppm per 10,000 gallons. Many charts round this to 1.5 lb. Muriatic acid removes one equivalent per 36.5 g of hydrogen chloride, which in 31.45% acid works out to 25.6 fl oz per 10 ppm per 10,000 gallons. Dry acid takes about 2.15 lb for the same drop.
The pH change after baking soda and the size of each acid round come from the same carbonate-chemistry model as our pH calculator. Stabilizer shows up in your alkalinity test as well, roughly a third of the CYA reading at normal pH, and the model accounts for it. Sources: How we calculate.
Questions people ask
How much baking soda raises alkalinity in a pool?
About 1.4 lb per 10,000 gallons for each 10 ppm. For a 20,000-gallon pool going from 70 to 100 ppm that is 1.4 × 2 × 3 = 8.4 lb. Add more than 30 ppm in two or more parts, a few hours apart.
How do I lower alkalinity without lowering pH?
You can't do it in one step. Lower both with acid, then raise pH back up by aerating the water, which does not change alkalinity. Repeat until alkalinity reaches your target.
Should I adjust alkalinity or pH first?
Alkalinity first. The chemicals that change alkalinity also move pH, so setting pH first only means doing it twice.
What happens if alkalinity is too low?
pH swings with every rainstorm and chlorine dose, and very low alkalinity with low pH corrodes heaters and etches plaster. Below about 60 ppm, raise it.
What happens if alkalinity is too high?
pH keeps drifting up, so you add acid again and again. High alkalinity with high pH also encourages scale and cloudy water.
Estimates only. Product strengths vary from jug to jug and lose strength with age, so treat every amount here as a starting point. Follow the product label, add in stages, and retest before swimming. For stubborn algae, equipment faults or surface damage, call a pool professional. Full disclaimer.