Pool Chlorine Calculator

How much of your chlorine product to add, with a target set by your stabilizer reading.

Pool volume (work it out)
How the pool gets chlorine

The strength is on the label. Liquid chlorine and bleach list it as "sodium hypochlorite ...%". Granules and tablets list "available chlorine ...%".

Chlorine to add

Fill in the boxes and your answer appears here.

How to use it

  1. Test free chlorine (FC) and stabilizer (CYA). A drop-test kit that reads FC in 0.5 ppm steps is far more reliable than strips for this.
  2. Enter both. The target fills in from your stabilizer level; you can overwrite it.
  3. Pick the product you have and check the strength on its label.
  4. Optional: enter how much chlorine your pool loses in a day to see the daily top-up amount.

Why the target depends on stabilizer

Stabilizer (cyanuric acid, CYA) shields chlorine from sunlight, but it also holds most of the chlorine in a weak, bound form. What kills algae and germs is the small free share left over, and that share depends on the ratio of chlorine to stabilizer. Research on chlorinated cyanurates shows it plainly: double the stabilizer and you need roughly double the chlorine for the same effect.

That is why "keep chlorine at 1 to 3 ppm" fails in so many backyard pools. At 30 ppm CYA, 3 ppm is fine. At 80 ppm CYA, 3 ppm lets algae grow. The public-pool code committee in the US recommended keeping stabilizer no higher than 20 times the free chlorine. We set the minimum at 7.5% of CYA for hand-dosed pools, which gives a margin for the chlorine the sun burns off between doses, and 5% for salt water pools.

Free chlorine for each stabilizer level. Salt water pools can run about a quarter lower because the generator adds chlorine all day.
Stabilizer (CYA)Minimum FCAim forShock level
0 ppm1310
20 ppm1.52.510
30 ppm2.53.512
40 ppm3416
50 ppm4520
60 ppm4.5624
70 ppm5.5728
80 ppm6832

Worked example

18,000 gallons, FC 1.5 ppm, CYA 40 ppm, 10% liquid chlorine.

The target for 40 ppm CYA is 4 ppm, so the pool needs 2.5 ppm more. 18,000 gallons is 68,140 liters; 2.5 mg per liter is 170 g of chlorine. Fresh 10% liquid chlorine carries about 110 g of chlorine per liter, so the dose is 1.55 liters: about 52 fl oz, a little over 1½ quarts.

How it's calculated

Grams of chlorine needed = rise in ppm × liters of water ÷ 1,000. That is divided by the chlorine content of the product.

  • Granules and tablets state available chlorine on the label (cal hypo 65% or 73%, dichlor 56% or 62%, trichlor 90%, lithium hypochlorite 35%). One pound of 65% cal hypo raises 10,000 gallons by about 7.8 ppm.
  • Liquid chlorine and bleach labels list sodium hypochlorite by weight. We convert that to chlorine per liter using the liquid's density: a fresh 12.5% product holds about 142 g of chlorine per liter, so one gallon raises 10,000 gallons by about 14 ppm. Many calculators assume 12.5 ppm. Ours is the fresh-jug figure; jugs lose strength in heat and storage, so retest and top up rather than adding extra up front.

The side effects come from the chemistry of each product: every ppm of chlorine from dichlor adds 0.9 ppm of stabilizer, trichlor adds 0.6 ppm, cal hypo adds about 0.7 ppm of calcium, and liquid chlorine leaves about 1.7 ppm of salt. Details and sources are on How we calculate.

Finding your daily loss

Test free chlorine at sunset and again at sunrise, then once more at sunset. The overnight drop shows what is being used up by dirt and organics; the daytime drop is mostly sunlight. A clean outdoor pool with proper stabilizer typically loses somewhere around 1 to 3 ppm a day in summer. Losing much more than that, or more than 1 ppm overnight, usually means something in the water is eating chlorine, often early algae.

Questions people ask

How much liquid chlorine do I add to my pool?

For 10,000 gallons, each 1 ppm rise takes about 11½ fl oz of 10% liquid chlorine, or about 9 fl oz of 12.5%. Multiply by the ppm you need and by your volume in ten-thousands of gallons. The calculator does this for you and suggests the ppm from your stabilizer reading.

Can I use household bleach instead of pool chlorine?

Yes, if it is plain unscented bleach with no added thickeners, scents or "splash-less" formula. It is the same chemical, just weaker, usually 6% to 8.25%. You need more of it: about 20½ fl oz of 6% bleach per ppm per 10,000 gallons.

What should my free chlorine level be?

It depends on your stabilizer (CYA). As a rule, keep free chlorine at no less than 7.5% of your CYA reading in a hand-dosed pool, and aim for about 10%. With 40 ppm of CYA that means at least 3 ppm, aiming for 4.

When is the best time to add chlorine?

In the evening. Sunlight breaks chlorine down quickly, so chlorine added at dusk has the whole night to work. Run the pump while you add it.

How long after adding chlorine can I swim?

Retest first. Many product labels say to wait until chlorine is 4 ppm or lower, while some allow more; the label on your product is the rule to follow. With liquid chlorine at normal doses, the water is usually mixed within 30 minutes to an hour of running the pump.

Estimates only. Product strengths vary from jug to jug and lose strength with age, so treat every amount here as a starting point. Follow the product label, add in stages, and retest before swimming. For stubborn algae, equipment faults or surface damage, call a pool professional. Full disclaimer.

Embed this calculator

Pool service companies and bloggers are welcome to put this calculator on their own site. Copy the code below. Please keep the credit line under it.

My Pool

Saved in this browser only. Nothing is sent to us. Every calculator fills itself in from here.