How to use it
- Test your water. A drop-test kit gives you free and combined chlorine, pH, alkalinity, calcium and stabilizer; salt pools also need a salt test.
- Enter your volume and every result you have. Open "Products you use" to set the chlorine and acid you keep on the shelf, with the strengths from their labels.
- Read the table: each reading is marked OK, low or high against the range for your type of pool.
- Follow the plan from the top. Each step has the amount, how to add it, and how long to wait before the next one.
- Save the readings if you want a history on this phone or computer, and print the plan to take outside.
Why the order matters
Pool chemicals pull on each other. Baking soda nudges pH up, acid pulls alkalinity down, and liquid chlorine raises pH for a few hours. Fix them in the wrong order and you end up adding the same chemical twice. The planner follows the order pool technicians use:
- Replace water first if stabilizer, calcium or salt is far too high. No chemical lowers them, and the refill changes every other number.
- Alkalinity, because it sets how pH behaves. When pH also needs acid, the planner adds extra baking soda to cover the alkalinity the acid will remove, so you land on target in one pass.
- pH, after the alkalinity is right.
- Chlorine, at least 30 minutes after any acid and in a different spot. Acid and chlorine must never meet in concentrated form.
- Calcium, once pH is in range, because adding calcium to high-pH water clouds it.
- Stabilizer and salt last. Both dissolve slowly and neither affects the steps before them.
Worked example
An 18,000-gallon plaster pool on liquid chlorine: FC 1, pH 7.9, alkalinity 60, calcium 250, stabilizer 30, 10% liquid chlorine and 31.45% muriatic acid on hand.
Alkalinity is low and pH is high. The planner first adds 8 lb 13 oz of baking soda in two parts. That takes alkalinity to about 95 ppm and pH to about 8.0. Then 22 fl oz of muriatic acid in two parts brings pH to 7.5, which also takes alkalinity down to the 90 ppm target. With 30 ppm of stabilizer, chlorine should sit at 2.5 ppm or more, so the last step is 52 fl oz of liquid chlorine at dusk, half an hour after the acid. Calcium 250 is fine for plaster, and the saturation index comes out at +0.14: balanced.
How it's calculated
Each reading is compared with the range for your pool: pH 7.4–7.6; alkalinity 80–100 ppm for liquid chlorine and cal hypo, 70–100 for salt water generators and 100–120 for tablets; calcium 200–400 ppm for plaster and 150–300 for vinyl and fiberglass; stabilizer 30–50 ppm, or 60–80 with a salt generator. Free chlorine is judged against your stabilizer reading, because stabilizer controls how strong the chlorine is.
Acid, soda ash and baking soda amounts come from a carbonate-chemistry model of your water, using pH, alkalinity, stabilizer and temperature together. That is what lets the planner predict how far pH moves after the baking soda and how much alkalinity the acid takes away. The saturation index uses the same model to judge whether the water leans toward etching or scale. Formulas, ranges and sources are on How we calculate.
All calculators
- Pool Volume CalculatorGallons or liters for any pool shape
- Pool Salt CalculatorPounds and bags of salt to reach your target
- Pool Chlorine CalculatorHow much chlorine to add, for any product
- Pool Shock CalculatorShock level set by your stabilizer reading
- Pool pH CalculatorRaise or lower pH with the right amount
- Pool Alkalinity CalculatorRaise or lower total alkalinity
- Stabilizer (CYA) CalculatorAdd stabilizer, or how much water to replace
- Calcium Hardness CalculatorCalcium chloride to add, or water to replace
- Saturation Index (LSI) CalculatorIs your water etching or scaling
- Partial Drain CalculatorHow much water to replace, and in how many rounds
- Hot Tub Chemical CalculatorChlorine or bromine, pH and more in teaspoons
- Green Pool Recovery PlannerDay-by-day plan to clear algae
- Cloudy Water TroubleshooterLikely causes and fixes for cloudy water
- Pool Opening PlanChecklist, chemicals and shopping list
- Pool Closing PlanWinterizing checklist and closing chemicals
- Pool Pump Size CalculatorFlow, head, pump size and run cost
- Pool Heater Size CalculatorHeater size, heat-up time and running cost
- Pool Fill CalculatorHow long filling takes and what it costs
- Pool Chemistry ChartPrintable target ranges and fixes
Your saved readings
Saved readings appear here.
Questions people ask
What order should I add pool chemicals in?
Alkalinity first, then pH, then chlorine, then calcium, then stabilizer and salt. If stabilizer, calcium or salt is far too high, partly drain and refill before anything else. Add one chemical at a time with the pump running.
How long should I wait between adding pool chemicals?
Run the pump at least 30 minutes between chemicals, and longer for some: 6 hours after a large baking soda dose before retesting alkalinity, a day after salt. Acid and chlorine always need at least 30 minutes between them and a different spot in the pool.
What are the ideal pool chemical levels?
pH 7.4–7.6, total alkalinity 80–100 ppm (lower with a salt generator, higher with tablets), calcium hardness 200–400 ppm for plaster, stabilizer 30–50 ppm (60–80 with a salt generator), and free chlorine of about 10% of your stabilizer reading.
Are test strips good enough for this calculator?
Strips are fine for a quick check of pH and to spot problems, but they read in wide steps. For chlorine, stabilizer and alkalinity, a drop-test kit is more precise, and precise readings give precise doses.
Does this work for hot tubs?
Hot tubs need different ranges and much smaller doses. A dedicated hot tub calculator is on the way. Until then, the chlorine calculator works for a hot tub if you enter its volume.
Estimates only. Product strengths vary from jug to jug and lose strength with age, so treat every amount here as a starting point. Follow the product label, add in stages, and retest before swimming. For stubborn algae, equipment faults or surface damage, call a pool professional. Full disclaimer.