How to use it
- Enter your pool volume and how often you want all the water to pass through the filter. Eight hours is the usual aim for a home pool.
- Describe the plumbing: pipe size, total length, elbows and how high the pump sits above the water. Rough numbers are fine.
- If you already have a pump, the filter pressure gauge gives a better answer than the plumbing estimate. Read it with a clean filter and the pump on high.
- Add watts and your electricity price to see what running it costs.
Flow and head, in plain terms
A pump is sized by two numbers, not by horsepower. Flow is how many gallons a minute you need: pool volume divided by the turnover time. Head is the resistance the pump pushes against, measured in feet of water: friction in the pipes and elbows, the filter, any heater or salt cell, the return fittings, and lifting water up to the pump. A pump's flow curve shows how much water it moves at each head; you want one that gives your flow at your head.
Most residential systems end up at 40 to 60 feet of head once the filter and heater are counted. Calculators that only count pipe friction come out far lower, and a pump chosen that way delivers less water than expected.
Worked example
A 20,000-gallon pool, 8-hour turnover, 2-inch pipe, 100 ft of pipe, six 90° elbows, two 45°, pump 2 ft above the water, sand filter, no heater.
Flow: 20,000 ÷ 480 minutes = 41.7 GPM. Pipe friction at that flow is about 2.9 ft per 100 ft of 2-inch PVC, so about 4 ft with the elbows. Add 15 ft for the sand filter and valve, 13 ft for return fittings and the suction side, and 2 ft of height: about 34 ft of head. Moving 41.7 GPM against 34 ft takes about 0.36 hydraulic horsepower, or roughly 0.9 hp from a small pump motor. A 1 hp pump covers it.
How it's calculated
- Flow (GPM) = gallons ÷ (turnover hours × 60).
- Pipe friction uses the Hazen-Williams equation for PVC, with elbows counted as extra pipe length (30 pipe diameters for a 90°, 16 for a 45°).
- Equipment losses use typical figures for clean equipment: sand filter and valve 15 ft, DE 10 ft, cartridge 8 ft, heater 10 ft, salt cell 4 ft, return fittings and valves 8 ft, suction side 5 ft. From a gauge: psi × 2.31 + 5 ft.
- Horsepower = GPM × head ÷ 3,960 ÷ 0.4, where 0.4 is a typical overall efficiency for a pool pump motor.
- Pipe limits: water speed of 6 ft per second on the suction side and 8 on the return side, the limits commonly used in pool design. Filter limits: sand 15, DE 2 and cartridge 0.375 GPM per square foot.
Why bigger is not better
An oversized pump pushes water faster than the filter can clean it, wears out seals and wastes electricity. Pump power rises with roughly the cube of speed, so a pump running at half speed uses about an eighth of the power. That is why US efficiency rules introduced in 2021 pushed most new in-ground pool pumps to variable speed: running slowly for longer does the same filtering for a fraction of the cost.
Questions people ask
What size pump do I need for my pool?
One that delivers your pool volume divided by 480 minutes (an 8-hour turnover) at your system's head. For most home pools of 15,000 to 25,000 gallons with 2-inch plumbing, that works out to about ¾ to 1½ hp, or a variable-speed pump.
How many hours a day should I run my pool pump?
Long enough to turn the water over at least once a day, which for most pools is 8 to 12 hours on a single-speed pump. Variable-speed pumps run longer at low speed, often 12 to 24 hours, and still use less power.
What is pool turnover?
The time it takes for a volume of water equal to the whole pool to pass through the filter. Eight hours is the common aim for home pools; public pools are often required to turn over in 6 hours or less.
Can a pool pump be too big?
Yes. Too much flow pushes dirt through sand and DE filters, can exceed what the pipes and fittings are designed for, and wastes electricity. Match the pump to the filter's rated flow.
Estimates only. Product strengths vary from jug to jug and lose strength with age, so treat every amount here as a starting point. Follow the product label, add in stages, and retest before swimming. For stubborn algae, equipment faults or surface damage, call a pool professional. Full disclaimer.