Calcium Hardness Calculator

Calcium chloride to raise hardness, or how much water to replace to bring it down.

Pool volume (work it out)
Pool surface

Your kit may report total hardness instead of calcium hardness. Total hardness includes magnesium and reads a little higher.

Calcium plan

Fill in the boxes and your answer appears here.

How to use it

  1. Test calcium hardness (CH) and choose your pool surface.
  2. Check the target: 300 ppm for plaster, pebble and concrete, 200 ppm for vinyl and fiberglass.
  3. Enter the strength from the bag. 77% (flakes) and 94% (pellets) are the usual ones.
  4. If you are over target, test your tap water too. The answer depends heavily on it.

Why calcium matters

Water with too little calcium pulls it from wherever it can. In a plaster pool that means the plaster itself: the surface turns rough and blotchy and grout joints wash out. Too much calcium does the opposite and drops out as white scale on tile, in the heater and inside salt cells, especially when pH and alkalinity are also high.

Vinyl and fiberglass don't contain calcium, so they can't be etched. They still benefit from a moderate level, which protects heaters and metal parts and makes foaming less likely.

Worked example

A 22,000-gallon plaster pool at 150 ppm, target 300 ppm, 77% calcium chloride.

The rise is 150 ppm. Each 10 ppm in 10,000 gallons takes 420 g of pure calcium chloride, or 1.2 lb of 77% flakes. So 1.2 × 15 × 2.2 = about 40 lb. That is more than a 100 ppm rise, so the calculator splits it over two days.

How it's calculated

Calcium hardness is reported as ppm of calcium carbonate. One mole of calcium chloride (111 g) supplies the same calcium as 100 g of calcium carbonate, so each ppm of hardness takes 1.11 mg of calcium chloride per liter, divided by the product strength. Lowering uses the same water-replacement formula as our drain calculator, including your fill water. Sources: How we calculate.

Common mistakes

Pouring dry calcium chloride straight into the pool. Undissolved pellets sit on the floor and can stain or etch it. Dissolve them in a bucket first.

Ignoring the tap water. In hard-water areas the fill water may already be at 250 ppm or more. Top-ups then raise calcium over the season, and draining can only bring it down to the tap water's level.

Cal hypo in hard water. Every ppm of chlorine from cal hypo adds about 0.7 ppm of calcium. Used all summer, it adds hundreds.

Questions people ask

How much calcium chloride do I add to raise hardness?

About 1.2 lb of 77% calcium chloride, or 1 lb of 94%, per 10,000 gallons raises calcium hardness by 10 ppm.

How do I lower calcium hardness in my pool?

Replace part of the water with fresh water that has less calcium. There is no practical chemical that removes calcium. Keeping pH and alkalinity on the low side prevents scale while hardness is high.

What should calcium hardness be in a vinyl pool?

About 150 to 300 ppm. Vinyl can't be etched, so lower levels don't harm the liner, but a moderate level protects heaters and metal parts.

Can I swim after adding calcium chloride?

Once it has dissolved and circulated, usually within an hour or so, calcium itself doesn't stop you swimming. Retest your chlorine and follow the product label.

Estimates only. Product strengths vary from jug to jug and lose strength with age, so treat every amount here as a starting point. Follow the product label, add in stages, and retest before swimming. For stubborn algae, equipment faults or surface damage, call a pool professional. Full disclaimer.

Embed this calculator

Pool service companies and bloggers are welcome to put this calculator on their own site. Copy the code below. Please keep the credit line under it.

My Pool

Saved in this browser only. Nothing is sent to us. Every calculator fills itself in from here.