How to use it
- Enter your pool volume, or save it once in My Pool.
- Test the salt with salt test strips or a digital salt meter and enter the reading.
- Choose your generator's range. The target fills in with the middle of that range; change it if your manual says otherwise.
- Enter your bag size. The answer shows pounds, full bags and the leftover amount.
Worked example
A 15,000-gallon pool reading 2,400 ppm, target 3,200 ppm, 40 lb bags.
The salt needs to rise 800 ppm. A gallon of water weighs 8.34 lb, so 15,000 gallons weigh 125,100 lb. 800 ppm of that is 125,100 × 800 ÷ 1,000,000 = 100 lb of salt. Pool salt is about 99% sodium chloride, so the tool asks for 101 lb: two full bags and about 21 lb from a third.
Filling a new 15,000-gallon pool from zero to 3,200 ppm takes about 404 lb, roughly ten 40 lb bags.
How it's calculated
ppm means pounds of salt per million pounds of water. The tool multiplies your gallons by 8.34 lb per gallon, multiplies by the rise in ppm, divides by one million, then divides by 0.99 for salt purity. A handy figure to remember: 10 lb of salt in 1,000 gallons raises the reading by about 1,200 ppm, or 1 lb per 1,000 gallons per 120 ppm.
If you are over the target, salt can't be taken out with chemicals. The only fix is replacing water. The share to replace is (current − target) ÷ (current − fill water salt). With 4,000 ppm in the pool, a 3,200 target and 200 ppm in the tap water, that is 800 ÷ 3,800 = 21%.
Common mistakes
Adding the whole amount on one reading. Salt readings swing by 200 to 300 ppm between test methods. For big additions the tool tells you to add three quarters, wait a day and retest. Overshooting means draining water.
Retesting too soon. Salt sitting on the floor or a reading taken next to the return jet will be wrong. Brush it in, run the pump for a full day, then test.
Forgetting that liquid chlorine adds salt. Each ppm of chlorine from liquid chlorine or bleach leaves about 1.7 ppm of salt behind once it is used up. Pools topped up with liquid chlorine all summer creep upward, which is why the over-target answer exists.
Full methods and sources: How we calculate.
Questions people ask
How much salt do I need for a 15,000 gallon pool?
From zero to 3,200 ppm, about 404 lb, or ten 40 lb bags. Topping up from 2,400 to 3,200 ppm takes about 101 lb. Most pools are topped up, not filled from zero.
What kind of salt can I use in a salt water pool?
Pure sodium chloride, at least 99% pure. Bags sold as pool salt are made for this. Avoid rock salt, iodized salt and salt with anti-caking additives, which can stain surfaces. Your generator manual lists what it accepts.
How long after adding salt can I turn the generator on?
Most generator manuals say to wait about 24 hours with the pump running so the salt dissolves and mixes. Retest first and switch the cell on once the reading is in range.
Can I swim after adding salt?
Pool salt is the same compound as table salt and sits at about a tenth of the saltiness of sea water. Once it has dissolved there is no swimming limit from the salt itself. Retest your chlorine before swimming, as always.
How do I lower the salt level in my pool?
Drain part of the water and refill with fresh water. The calculator works out how much when your reading is above target. Rain and backwashing also lower salt over time.
Estimates only. Product strengths vary from jug to jug and lose strength with age, so treat every amount here as a starting point. Follow the product label, add in stages, and retest before swimming. For stubborn algae, equipment faults or surface damage, call a pool professional. Full disclaimer.