How to use it
- Enter your hot tub's volume. It is in the owner's manual or on the maker's website, and most tubs hold 300 to 500 gallons.
- Pick chlorine or bromine, then enter your test results. Test with the jets off and the water at its usual temperature.
- Check "Products you use". The calculator assumes dichlor granules and dry acid, the usual hot tub products.
- Add things in the order shown, one at a time, with the jets running and the cover open.
Why hot tubs need different numbers
A hot tub is a small amount of very warm water shared by several people, often every day. Body oils, sweat and lotions use up sanitizer fast, and warm water grows germs faster. That is why the public health code minimum for spas is higher than for pools: 3 ppm of free chlorine or 4 ppm of bromine, compared with 1 ppm in a pool.
The small volume also means tiny doses. In a 400-gallon tub, a single teaspoon of the wrong product moves the readings a long way. The calculator gives teaspoons and grams for small amounts; a cheap kitchen scale makes dosing much more accurate.
Hot water scales more easily than pool water, so calcium is kept lower (150–250 ppm) and pH no higher than 7.6.
Chlorine or bromine
Chlorine is cheaper and works quickly. Dichlor, the usual spa chlorine, adds stabilizer with every dose, and that builds up until the water is changed. Bromine holds up better in hot water and smells less, but it has to be reactivated: bromine tablets keep a store of bromide in the water, and a weekly dose of shock (chlorine or non-chlorine) turns the used bromide back into active bromine. Don't switch between the two without draining first.
Worked example
A 400-gallon tub, chlorine 1 ppm, pH 7.9, alkalinity 100 ppm, 102°F, 56% dichlor and 93.2% dry acid.
Lowering pH to 7.5 in 400 gallons takes about 14 g of dry acid, roughly half an ounce. Thirty minutes later, raising chlorine from 1 to 4 ppm takes 3 mg per liter across 1,514 liters, 4.5 g of chlorine, which is about 8 g of dichlor, a little under 2 teaspoons. That dose also adds about 3 ppm of stabilizer.
How it's calculated
The chemistry is the same as for pools, scaled to the tub. Chlorine doses use the product's available chlorine. Bromine readings convert to chlorine at 2.25 ppm of bromine per ppm of chlorine, the ratio of their molecular weights, which bromine test kits use too. pH doses come from our carbonate model run at hot tub temperature. The water change interval uses the common industry rule: tub volume in gallons ÷ 3 ÷ average soakers per day. Sources: How we calculate.
Questions people ask
How much chlorine do I put in a hot tub?
Enough to keep free chlorine at 3 to 5 ppm. In a 400-gallon tub, each 1 ppm takes about 2.7 g of 56% dichlor, a bit over half a teaspoon. After a busy soak you usually need 2 to 3 ppm more.
What should bromine be in a hot tub?
4 to 6 ppm. Below 4, bromine can't keep up with the load from bathers in hot water.
How often should I change my hot tub water?
A common rule is tub volume in gallons divided by 3, divided by the average number of people using it each day. A 400-gallon tub used by two people a day needs fresh water about every 67 days. Change it sooner if it foams, smells or won't hold sanitizer.
Can I use pool chemicals in my hot tub?
Mostly yes, if they are the same chemical: liquid chlorine, dichlor, sodium bisulfate, soda ash and baking soda are the same in either. Avoid trichlor tablets, which push pH and alkalinity down in such a small volume, and cal hypo, which raises calcium and can cloud hot water.
Why does my hot tub pH keep going up?
The jets and air blowers drive carbon dioxide out of the water, which raises pH. High alkalinity makes it climb faster. Lower alkalinity toward 80 ppm and pH will drift less.
Estimates only. Product strengths vary from jug to jug and lose strength with age, so treat every amount here as a starting point. Follow the product label, add in stages, and retest before swimming. For stubborn algae, equipment faults or surface damage, call a pool professional. Full disclaimer.