How to use it
- Test stabilizer (CYA). Most drop kits measure it with a cloudiness test read against a black dot; read it in good daylight with your back to the sun.
- Choose how your pool gets chlorine. The target fills in at 40 ppm for pools chlorinated by hand and 70 ppm for salt water pools.
- Below target, you get the amount of stabilizer to add. Above it, you get how much water to replace, in one go or in rounds.
What stabilizer does
Sunlight destroys unprotected chlorine fast: an outdoor pool with no stabilizer can lose most of its chlorine in a couple of hours of midday sun. Cyanuric acid holds chlorine in a form that sunlight can't break down, so the chlorine lasts all day. The cost is that it also slows the chlorine down, which is why the right chlorine level rises with your stabilizer reading.
That trade-off sets the target. Around 30 to 50 ppm gives good sun protection without needing a lot of chlorine. Salt water generators make chlorine in small amounts all day, so a higher level of 60 to 80 ppm keeps that chlorine from burning off. Check your generator manual; a few ask for less.
Worked examples
Raising: a new 20,000-gallon fill at 0 ppm, target 40 ppm. 40 mg per liter in 75,710 liters is 3,028 g of cyanuric acid. At 99% strength that is about 3,060 g: 6 lb 12 oz. Rule of thumb: about 13 oz per 10 ppm per 10,000 gallons.
Lowering: 15,000 gallons at 100 ppm, target 50 ppm. Half the water has to go: 7,500 gallons. In two rounds, each round replaces 29% (about 4,390 gallons), 8,790 gallons in all. Rounds use more water but never leave the pool half empty.
How it's calculated
Raising: grams = ppm rise × liters ÷ 1,000 ÷ strength. Lowering: the share of water to replace is (current − target) ÷ (current − fill water). For several equal rounds, each round replaces 1 − ((target − fill) ÷ (current − fill))^(1 ÷ rounds). Free chlorine targets for the new stabilizer level come from the chlorine-to-stabilizer ratio explained on How we calculate.
Where high stabilizer comes from
Almost always from stabilized chlorine. Every ppm of chlorine from trichlor tablets adds 0.6 ppm of stabilizer, and every ppm from dichlor adds 0.9 ppm. A pool that uses 2 ppm of chlorine a day from tablets gains about 36 ppm of stabilizer a month. Rain, splash-out and backwashing take some out, but in a dry summer the reading climbs steadily. Once it passes your target, switch to liquid chlorine or cal hypo, which add none.
Questions people ask
How do I lower cyanuric acid in my pool?
Replace part of the water. Stabilizer does not break down with normal chlorine levels, and enzyme "reducer" products only work in some pools. To go from 80 to 40 ppm, replace half the water with fresh water.
How much stabilizer do I add to my pool?
About 13 oz of dry stabilizer per 10,000 gallons raises the level by 10 ppm. A 15,000-gallon pool going from 10 to 40 ppm needs about 3 lb 13 oz.
How long does stabilizer take to dissolve?
Two days or more, sometimes up to a week before the test shows the full amount. Keep the pump running, don't backwash for two days, and wait a week before adding more.
What is too high for cyanuric acid?
Public pool codes in the US cap it at 90 to 100 ppm. Above about 80 ppm in a hand-chlorinated pool, the chlorine needed to keep algae away becomes impractical and partial draining is the cheaper fix.
Do indoor pools need stabilizer?
No. Stabilizer protects chlorine from sunlight. Indoor pools and covered hot tubs get little or no benefit from it.
Estimates only. Product strengths vary from jug to jug and lose strength with age, so treat every amount here as a starting point. Follow the product label, add in stages, and retest before swimming. For stubborn algae, equipment faults or surface damage, call a pool professional. Full disclaimer.