How to use it
- Test pH, total alkalinity (TA) and stabilizer (CYA). All three change the answer.
- Enter a target. 7.5 is a good aim for almost every pool; the calculator works out whether to raise or lower.
- Choose the acid or base you have. Strength is on the label: muriatic acid is usually 31.45% or about 14.5% for the "half-strength" jugs.
- Add the dose in the parts shown and retest between them.
Why alkalinity changes the dose
Alkalinity is the water's resistance to a pH change. The 11 fl oz of acid that takes a 10,000-gallon pool at 80 ppm alkalinity from pH 7.8 to 7.4 only gets the same pool at 140 ppm to about 7.5. Many pH calculators assume an alkalinity of 100 for everyone, which is why their answers are so often off.
Stabilizer adds to this resistance too. At the usual pool pH, cyanuric acid soaks up part of every acid dose, so a pool at 60 ppm CYA needs roughly a third more acid for the same pH drop than one with none.
One more thing makes this calculator different: lowering pH and raising it are not mirror images. Raising pH by half a point usually takes more soda ash by weight than lowering it takes acid, because the water's buffering is stronger below 7.5.
Worked example
12,000 gallons, pH 7.9, TA 100 ppm, CYA 40 ppm, 31.45% muriatic acid, target 7.5.
At pH 7.9 the alkalinity of 100 ppm is mostly bicarbonate. Lowering to 7.5 turns some of it into carbonic acid, and the stabilizer soaks up a share too. Together that takes about 0.094 milliequivalents of acid per liter. Across 45,420 liters that is 4.3 equivalents, or 156 g of hydrogen chloride. In 31.45% acid that is about 430 ml: roughly 14½ fl oz. Alkalinity drops by about 5 ppm along the way.
How it's calculated
The calculator models the water's carbonate chemistry, the same equilibrium chemistry used in water treatment. From your pH, alkalinity, stabilizer and temperature it works out how much dissolved carbonate the water holds, then how much acid (or soda ash, or borax) moves the balance to your target pH. Temperature-dependent constants come from published carbonate equilibrium data, and stabilizer and borates are included as extra buffers.
For safety the dose is split when it is large: acid is divided into parts of no more than about a quart of 31.45% acid per 10,000 gallons, or a 0.4 pH drop, whichever comes first; soda ash is split every 0.3 pH. Full details: How we calculate.
Common mistakes
Chasing pH with a high alkalinity. If alkalinity is above about 120 ppm, pH will climb back within days no matter how often you add acid. Lower the alkalinity instead.
Testing right after adding chlorine. Liquid chlorine and cal hypo raise pH for a few hours after you add them. Test pH before adding chlorine, or wait until the next morning.
Testing with high chlorine. Above about 10 ppm, chlorine bleaches the pH indicator dye and gives a false high reading. Most drop kits say so on the instructions.
Questions people ask
How do I lower the pH in my pool?
Add muriatic acid or dry acid (sodium bisulfate). For a typical 10,000-gallon pool with alkalinity around 100 ppm, about 12 to 14 fl oz of 31.45% muriatic acid lowers pH from 7.8 to 7.4; the higher figure applies with 30 ppm or more of stabilizer. Pour it into the deep end with the pump running and retest after 30 minutes.
How do I raise the pH in my pool?
Use soda ash (sodium carbonate) or borax. If alkalinity is also low, start with baking soda instead, which raises alkalinity and nudges pH up slightly. Aerating the water, with fountains or returns pointed upward, raises pH slowly without chemicals.
What causes high pH in a pool?
Carbon dioxide escaping from the water, which pushes pH up. It happens faster with high alkalinity, splashing, waterfalls, spa spillovers and salt water generators. Fresh plaster also raises pH for its first months.
Is it safe to swim with high pH?
A pH up to about 7.8 is normal. Above 8, chlorine works more slowly, water can turn cloudy and scale can form on surfaces and in heaters, and swimmers may notice dry skin and eye irritation. Bring it down before it reaches that point.
Can I add acid and chlorine at the same time?
No. Acid and chlorine together release chlorine gas. Add one, let the pump run for at least 30 minutes, then add the other, in a different spot. Never mix them in a bucket or pour one into a container that held the other.
Estimates only. Product strengths vary from jug to jug and lose strength with age, so treat every amount here as a starting point. Follow the product label, add in stages, and retest before swimming. For stubborn algae, equipment faults or surface damage, call a pool professional. Full disclaimer.